TDEB Top Bar

Trending
Semiconductor Industry News — The Digital Electronics Blog
Follow Us

TDEB Masthead

The Semiconductor Hub

Semiconductors.  Chips and Systems.  Innovation.

Indexed by leading Search Engines, AI and referenced by Engineers worldwide 500+ Articles 10M+ Pageviews 30+ Reports 50+ Citations

Clock Jitter: What It Is and Why It Matters

The Editor's Desk
by
0
Share Facebook X LinkedIn WhatsApp Email

Clock jitter is the deviation of clock edges from their ideal timing. Because that deviation eats into the time available to capture data and degrades high-speed links and data converters, jitter must be kept to a minimum in a high-speed system.

High-speed signaling is very sensitive to jitter. As signals toggle faster, the transmitter and receiver face tighter limits. In many high-speed data applications the clock edge must fall within a narrow window to capture data correctly. The more jitter in a system, the more often the edge falls outside that window, and how often that happens shows up as the system's bit error rate (BER).

What jitter is, in plain words

Picture a perfect clock as a row of edges spaced exactly one period apart. A real clock's edges wander a little early or late around those ideal positions. That wander is jitter. National Instruments puts it simply: jitter is the difference between when an event should happen and when it actually happens (NI, Digital Timing: Clock Signals, Jitter, Hysteresis, and Eye Diagrams).

Jitter is small, usually picoseconds or less, but a fast clock has very little time to spare. At 1 GHz a whole clock period is only 1,000 ps, and at 10 Gb/s one bit lasts just 100 ps.

Where it comes from

  • Random sources: thermal and other device noise in oscillators, PLLs and clock buffers. This part is unbounded in principle and is described statistically.
  • Deterministic sources: power supply noise, crosstalk from neighboring signals, simultaneous switching outputs, and data-dependent effects on a channel. This part is bounded and often repeats.

Why it matters

  • Digital timing: inside a chip, jitter shortens the effective clock period, so less time is left for logic between flip-flops.
  • Serial links: in SerDes, Ethernet and PCIe receivers, jitter closes the data eye and raises the bit error rate.
  • Data converters: an ADC samples at the clock edge, so a mistimed edge samples the wrong voltage. Texas Instruments shows that with fast input signals, clock jitter becomes the main limit on an ADC's signal-to-noise ratio (TI, Clock jitter analyzed in the time domain, Part 1).

How engineers keep it down

  • Use a clean reference oscillator and a PLL with suitable loop bandwidth.
  • Give PLLs and clock buffers their own quiet, well-decoupled supplies.
  • Route clocks away from aggressors and keep the clock tree short and balanced.
  • Budget jitter explicitly in timing analysis and link design rather than hoping margin covers it.

Deep dive: the numbers and details

This part holds the definitions, equations and worked examples. Skip it if the overview is all you need.

Ways to measure jitter

MeasureWhat it comparesTypical use
Period jitterEach clock period against the ideal periodSetup timing inside a chip
Cycle-to-cycle jitterEach period against the one before itPLL and oscillator data sheets
Time interval error (TIE)Each edge against its ideal positionSerial links, long-term accumulation
Phase jitterPhase noise integrated over a frequency bandReference clocks for transceivers and ADCs

Each figure can be quoted as an rms value or as a peak-to-peak value. Always check which one a data sheet gives; the two differ by a large factor.

Random and deterministic jitter

Total jitter (TJ) depends on how rare an error you are willing to accept. The dual-Dirac model splits jitter into a deterministic part (DJ, peak-to-peak) and a random, Gaussian part (RJ, rms), then estimates TJ at a chosen BER:

TJ(BER) = DJ + alpha(BER) x RJ          alpha = about 14 at BER = 1e-12

The value of about 14 for BER 10-12 is the one used by Teledyne LeCroy in its description of the model (Teledyne LeCroy, Understanding SDA II jitter calculation methods).

Worked example (illustrative values): a 10 Gb/s link has a unit interval of 100 ps. With DJ = 10 ps and RJ = 1 ps rms, TJ at 10-12 is about 10 + 14 x 1 = 24 ps, or 24% of the bit time. Note how the 1 ps of random jitter contributes more than the 10 ps of deterministic jitter at this error rate.

Jitter in static timing analysis

For a path between two flip-flops on the same clock, the setup check with jitter is:

T_clk - t_jitter  >=  t_clk-to-q + t_logic + t_setup  (+ clock skew terms)

In STA tools the jitter usually goes into the clock uncertainty value. Example: a 1 GHz clock (1,000 ps) with 30 ps of period jitter leaves 970 ps for the path, so 3% of the cycle is gone before any logic is placed. Hold checks compare launch and capture on the same edge, so cycle jitter largely cancels there; teams usually apply a smaller hold uncertainty.

Jitter and ADC signal-to-noise ratio

For a sine wave input of frequency fIN sampled with rms jitter tJ, the jitter-limited SNR is:

SNR_jitter (dBc) = -20 x log10(2 x pi x f_IN x t_J)

TI's example: 400 fs of jitter at a 100 MHz input limits SNR to about 72 dBc, whatever the converter's resolution (TI SLYT379). Doubling the input frequency costs 6 dB. Independent random jitter sources, such as the clock and the ADC's own aperture jitter, add as the square root of the sum of squares:

t_J,total = sqrt(t_J,clock^2 + t_J,aperture^2)

Common mistakes

  • Adding rms jitter values linearly instead of root-sum-square, which overstates random jitter.
  • Mixing rms and peak-to-peak numbers from different data sheets.
  • Quoting phase jitter without the integration band; the same oscillator gives different numbers over different bands.
  • Forgetting that a PLL can pass, filter or amplify reference jitter depending on its loop bandwidth.
  • Using a total-jitter figure without stating the BER it applies to.

Further reading

The Editor's Desk
About the Author
The Editor's Desk
Share Facebook X LinkedIn WhatsApp Email

Post a Comment

0 Comments

Your comments will be moderated before it appears here.

Post a Comment (0)

#buttons=(Ok, Go it!) #days=(20)

Our website uses cookies to enhance your experience. Learn more
Ok, Go it!