Verilog
Delay modelling is how an HDL simulation represents the time a gate or wire takes to respond. The two models that matter in practice are inertial delay, where pulses shorter than the delay are swallowed, and transport delay, where every input change appears at the output after the delay, however short. In Verilog, a delayed continuous assignment gives inertial behaviour, and a delay on the right-hand side of a nonblocking assignment gives transp…
by
The Editor's Desk
March 27, 2007
Semiconductor Industry
How long do you think DVDs have around? 20 years? 10 years? Actually, they have only been around for about seven years, but it seems like they have been around much longer. Many of us can remember life before DVDs with VCDs and though they still exist their popularity has reduced drastically. That can be attributed to how rapidly we can become acclimated to some innovations in electronics technology. I believe there are other electronics technol…
by
Murugavel Ganesan
December 29, 2006
Verification
Gate level simulation comes in two main forms. Unit delay simulation runs the synthesised netlist with small fixed delays and no timing checks, to verify reset, scan and basic function quickly. Full timing simulation back-annotates real cell and wire delays and timing checks from an SDF file onto the post-layout netlist, to confirm the chip works with its real timing. This part of the series explains when each is used and how to set them up. G…
by
The Editor's Desk
November 30, 2006
EDA Tools
http://www.eetimes.com/news/design/resources/edaterms.html
by
The Editor's Desk
November 10, 2006
Verilog
This article contains some thoughts of mine about how and engineer should write Verilog code for Synthesis, general rules that will save you headaches if you follow, and how a Verilog file should be layed out. Rules: If you don't know what hardware the code you just wrote is, neither will the synthesizer. Remember that Verilog is a Hardware Description Language (HDL) and as such it describes hardware not magical circuits that you can never …
by
The Editor's Desk
November 02, 2006
Processors
Some web resources, references, labs, and slides. http://esd.cs.ucr.edu/
by
The Editor's Desk
November 02, 2006
Tutorials
Logic synthesis is a process by which an abstract form of desired circuit behavior, typically register transfer level (RTL) or behavioral is turned into a design implementation in terms of logic gates. Some tools can generate bitstreams for programmable logic devices such as PALs or FPGAs, while others target the creation of ASICs. Logic synthesis is one aspect of electronic design automation. History of Logic Synthesis The roots of logic synthe…
by
The Editor's Desk
October 19, 2006
Verilog
The history of the Verilog HDL goes back to the 1980s, when Gateway Design Automation developed Verilog-XL logic simulator, and with it a hardware description language.Cadence Design Systems acquired Gateway in 1989, and with it the rights to the language and the simulator. In 1990, Cadence put the language into the public domain, with the intention that it should become a standard, non-proprietary language. The Verilog HDL is now maintained by …
by
Aarthi Chinappa
October 19, 2006
Opinion
We are happy to invite you as a contributor to this blog in digital electronics. Of course, you can choose to be anonymous like us or choose an alias for convenience. Please be advised that we don't tolerate posting of proprietary information specific to any company and that you obey the copyrights. We are not responsible in anyways for any copyright infringements by the contributers. A Metastable State is the sole owner of this blog. Please…
by
The Editor's Desk
October 18, 2006
News
After much awaited delay due to developments on the blogger in beta, i m happy to announce that i have successfully converted/moved to beta. This enables me to mainly.. categorize posts(labelling is needed) display the latest comments on the sidebar(to be added) etc. add relevant links etc. I hope you will like it new. As you have already noticed, i have started a new series in Gate Level Simulation (GLS). This will take time and would appreciat…
by
The Editor's Desk
October 16, 2006
Verification
Gate level simulation (GLS) is the simulation of a synthesised or post-layout netlist, built from standard cells and flip-flops, instead of the RTL it came from. Teams still run it, even with mature static timing analysis (STA) and formal equivalence checking (LEC), because GLS catches the things those static tools assume away: reset and boot problems, X behaviour that RTL hides, inserted test logic, wrong timing constraints and real switching a…
by
The Editor's Desk
October 16, 2006
Verification
Power gating changes what RTL means. When a block can be switched off, the design gains power switches, isolation cells, retention registers and level shifters that are usually not written in the RTL at all, plus control signals (switch enable, isolation enable, save and restore) that the RTL generates but that drive nothing until implementation adds those cells. Functional verification has to model all of that, in the right order, or the simula…
by
The Editor's Desk
October 03, 2006
Tutorials
Lets take a look at the various low power techniques in use today. I would classify them into 2 categories Structural Techniques Voltage Islands Multi-threshold devices Multi-oxide devices Minimize capacitance by custom design Power efficient circuits Parallelism in micro-architecture Traditional Techniques Clock gating Power gating Variable frequency Variable voltage supply Variable device threshold Which one of the above techniques are ai…
by
The Editor's Desk
October 03, 2006
Tutorials
Special cells are required for implementing a Multi-Voltage design. Level Shifter Isolation Cell Enable Level Shifter Retention Flops Always ON cells Power Gating Switches/MTCMOS switch Level Shifter: Purpose of this cell is to shift the voltage from low to high as well as high to low. Generally buffer type and Latch type level shifters are available. In general H2L LS's are very simple whereas L2H LS's are little complex and are in g…
by
The Editor's Desk
October 03, 2006
Tutorials
Before we start looking at implementing a Multi-Voltage design there are certain questions that need to be answered to find out from process/library perspective such as Available Operating Voltages (PVT) Do we have special cells such as Level Shifters/Isolation cells/Power Gating Switches? If Level Shifter exists, what kinds of level shifters are available? (Ex: Enable Level Shifter etc) What are the different c…
by
The Editor's Desk
September 28, 2006
Tutorials
In the last few weeks i have been quite busy with a lot of research on low power design. There are so many tutorials on Low Power and everyone's concerns/questions seems to be dancing around Multi-Voltage design. What I could sense was there were lot of designers Implementing Multi-Supply(Power-Gating) as opposed to real Multi-Voltage design. There are 3 classics style of new design style i found Multi-Supply(Power Gating) Static Multi-…
by
The Editor's Desk
September 28, 2006
Tutorials
Multi-Vt cells are standard cells built in several threshold-voltage flavours (for example low, standard and high Vt) with the same footprint, so a tool can swap a fast, leaky cell for a slower, low-leakage one without moving anything. The catch is that each Vt flavour is defined by its own implant or Vt-setting layer, and those layers have minimum width, spacing and area rules. When cells of different Vt types sit next to each other, or a narro…
by
The Editor's Desk
September 28, 2006
Verification
By popular demand: Event simulation allows the design to contain simple timing information - the delay needed for a signal to travel from one point to another. During simulation, signal changes are tracked in the form of events. A change at a certain time triggers an event after a certain delay. Events are sorted by time when they will occur, and when all events for a particular time have been handled, the simulated time is advanced to the time …
by
The Editor's Desk
August 31, 2006
News
Last 2 weeks has witnessed a sudden surge in visitors and so i decided to continue my experiments for some more time with some new information or updates on some old articles. I will try to make some time to answer your questions and queries. Thanks
by
The Editor's Desk
March 07, 2006
News
I have found that this Blog has not attracted enough enthusiasts as expected. So due to lack of participation i m forced to limit my posts. If you want me to update this Blog at a regular pace, please participate actively by commenting and by making proposals. AUTHOR
by
The Editor's Desk
February 26, 2006
Interview Questions
What are the representations for, zero in 2's compliment the most positive integer that can be represented using 2's compliment the most negative integer that can be represented using 2's compliment Give the 8-digit hexadecimal equivalent of 37 10 -32768 10 11011110101011011011111011101111 2 Do the following using 6-bit 2's complement arithmetic (a fancy way of saying, ordinary addition in base 2 keeping only 6 bits of…
by
The Editor's Desk
January 24, 2006
Static Timing Analysis
You get the final chip back from the FAB. Now you do the smoke test(power up). Hopefully assuming that things are well (your chip does not go up in smoke) you do the first actual test of data using a sample and a simple test case. Unfortunately the chip does not seem to function as you it is intended to. How do you know if your chip has a setup time or a hold time problem?
by
The Editor's Desk
January 22, 2006